DSpace Arşivi :: by Yazar "Kaya, H." değerine göre listeleniyor

Yazar "Kaya, H." seçeneğine göre listele

Listeleniyor 1 - 20 / 51

A study of microstructure and solidification behaviour of Zn-Cu alloy
(REDAKCIA KOVOVE MATERIALY, 2010) Boyuk, U.; Engin, S.; Kaya, H.; Cadirli, E.; Marasli, N.; Keslioglu, K.
Zn-1.5wt.%Cu peritectic alloy was prepared in a graphite crucible under a vacuum atmosphere. Unidirectional solidification of Zn-1.5wt.%Cu peritectic alloy was carried out with the Bridgman method by using metals of 99.99 % purity under the argon atmosphere and two different conditions; with a temperature gradient (G) range of 1.99-7.81 K mm(-1) at constant growth rate (V) and a growth rate range of 8.41-661.11 mu m s(-1) at a constant temperature gradient. The microstructures of the directionally solidified Zn-1.5wt.%Cu peritectic samples were observed to be cellular. From both transverse and longitudinal sections of the samples, cellular spacing (lambda), and cell tip radius (R) were measured and expressed as functions of solidification processing parameters (G and V) using a linear regression analysis. The experimental results were also compared with values calculated according to the current theoretical and numerical models, and similar previous experimental results.
Dendritic growth in an aluminum-silicon alloy
(ASM INTERNATIONAL, 2007) Kaya, H.; Cadirli, E.; Guenduez, M.
Unidirectional solidification experiments have been carried out on an Al-3 wt.% Si alloy as a function of temperature gradient, G and growth rate, V. The samples were solidified under steady-state conditions with a constant growth rate of 8.20 mu m/s at different temperature gradients (1.97-6.84 K/mm) and with a constant temperature gradient (6.84 K/mm) at different growth rates (8.20-492.76 mu m/s). Microstructure parameters (primary dendrite arm spacing, lambda(1), secondary dendrite arm spacing, lambda(2), dendrite tip radius, R and mushy zone depth, d) were measured as a function of temperature gradient and growth rate. The experimental results have been compared with the current theoretical models and similar experimental works.
Dendritic growth of the binary succinonitrile-camphor system
(WORLD SCIENTIFIC PUBL CO PTE LTD, 2007) Cadirli, E.; Kaya, H.
Succinonitrile (SCN)-2wt% Camphor (CAMP) alloy was unidirectionally solidified with a constant temperature gradient (G=3.01 K/mm) at different growth rates (V=6.5- 113 mu m/s) and with a constant growth rate (V=6.5 mu m/s) at different temperature gradients (G=1.93- 3.01 K/mm). Microstructural parameters (primary dendrite arm spacings, lambda(1), secondary dendrite arm spacings, lambda(2), dendrite tip radius, R, and mushy zone depth, d) were measured as a function of growth rate and temperature gradient. The experimental results have been compared with theoretical models and previous experimental works. The stability constant (sigma) for this alloy system was calculated and compared with similar experimental results.
Dependence of Electrical Resistivity on Temperature and Sn Content in Pb-Sn Solders
(SPRINGER, 2011) Cadirli, E.; Boyuk, U.; Kaya, H.; Marasli, N.; Aksoz, S.; Ocak, Y.
Pb(100-x)-Sn-x solders (x = 5 wt.%, 10 wt.%, 20 wt.%, 35 wt.%, 50 wt.%, 60 wt.%, 61.9 wt.%, and 95 wt.%) were directionally solidified upward with a constant growth rate (V = 37.4 mu m/s) in a temperature gradient (G = 4.8 K/mm) in a Bridgman-type growth apparatus. The variations of electrical resistivity (rho) with temperature in the range of 323 K to 423 K for the directionally solidified Pb-Sn solders were measured. The present measurements indicate that the electrical resistivity of the directionally solidified Pb-Sn solders increases with increasing temperature, whereas the resistivity of the Pb-Sn solders decreases with increasing Sn content. The dependency of the Lorenz number (L) on temperature and Sn content for the Pb-Sn solders was also investigated based on the Wiedemann-Franz law by using the measured values of the thermal (K) and electrical (sigma) conductivity for the same alloys.
Dependency of microindentation hardness on solidification processing parameters and cellular spacing in the directionally solidified Al based alloys
(ELSEVIER SCIENCE SA, 2009) Kaya, H.; Guenduez, M.; Cadirli, E.; Marasli, N.
Al based alloys (Al-0.1 wt.%Ti, Al-05 wt.%Ti and Al-2 wt.%Li) were prepared using metals of 99.99% high purity in the vacuum atmosphere. These alloys were directionally solidified upward with the different temperature gradients, G, at a constant growth rate, V, and also with the different V at a constant G in the directional solidification apparatus. Cellular spacing, lambda, and microindentation hardness, HV, were measured from both transverse and longitudinal sections of the specimen as a function of solidification processing parameters (G, V and cooling rate, (T) over dot). Dependency of microindentation hardness on the solidification processing parameters and cellular spacing (lambda) in the directionally solidified aluminum alloys were experimentally investigated and the relationships between the solidification processing parameters and microindentation hardness, and cellular spacing and microindentation hardness were obtained by linear regression analysis. The results obtained in this work have been compared with the previous similar experimental results obtained for binary alloys. (C) 2008 Elsevier B.V. All rights reserved.
Dependency of Microstructural Parameters and Microindentation Hardness on the Temperature Gradient in the In-Bi-Sn Ternary Alloy with a Low Melting Point
(KOREAN INST METALS MATERIALS, 2008) Kaya, H.; Boyuk, U.; Cadirli, E.; Ocak, Y.; Akbulut, S.; Keslioglu, K.; Marasli, N.
The ternary alloy In-21.5 at.% Bi-17.8 at.% Sn, which has a melting point of 60 degrees C, was directionally solidified upward with a constant growth rate (V = 3.2 mu m/s) and different temperature gradients (G = 0.91 K/mm to 2.85 K/mm) by using a Bridgman-type directional solidification furnace. The lamellar spacings (lambda) and microhardness (H(v)) were measured from both the transverse and longitudinal sections of the samples. The dependence of the lamellar spacings (lambda) and microhardness (H(v)) on the temperature gradients (G) were determined by means of linear regression analysis. According to these results, the value of lambda decreases as the value of G increases and the value of Hv increases for a constant V. The results obtained in this work are compared with previous similar experimental results obtained for binary or ternary alloys.
Dependency of the thermal and electrical conductivity on the temperature and composition of Cu in the Al based Al-Cu alloys
(ELSEVIER SCIENCE INC, 2010) Aksoz, S.; Ocak, Y.; Marasli, N.; Cadirli, E.; Kaya, H.; Boyuk, U.
The variations of thermal conductivity with temperature for Al-[x] wt.% Cu, x = 3, 6, 15 and 24 alloys were measured by using a radial heat flow apparatus. The variations of electrical conductivity of solid phases versus temperature for the same alloys were determined from the Wiedemann-Franz and Smith-Palmer equations by using the measured values of thermal conductivity. From the graphs of thermal and electrical conductivity versus temperature, the thermal conductivity of the solid phases at their melting temperatures, and the thermal temperature and the electrical coefficients for the same alloys were obtained. Dependency of the thermal and electrical conductivity on the composition of Cu in the Al based Al-Cu alloys were also investigated. According to present experimental results, the thermal and electrical conductivity of Al-[x] wt.% Cu, x = 3, 6, 15 and 24 alloys linearly decrease with increasing the temperature and composition of Cu. The enthalpy of fusion and the specific heat change during the transformation for the same alloys were determined from cooling trace during the transformation from eutectic liquid to eutectic solid by means of differential scanning calorimeter (DSC). (c) 2010 Elsevier Inc. All rights reserved.
Determination of Interfacial Energies for Solid Al Solution in Equilibrium with Al-Cu-Ag Liquid
(KOREAN INST METALS MATERIALS, 2010) Keslioglu, K.; Ocak, Y.; Aksoz, S.; Marasli, N.; Cadirli, E.; Kaya, H.
The equilibrated grain boundary groove shapes of a solid Al solution in equilibrium with Al-Cu-Ag liquid were observed from a quenched sample using a radial heat flow apparatus. The Gibbs-Thomson coefficient, solid-liquid interfacial energy, and grain boundary energy of the solid Al solution were determined from the observed grain boundary groove shapes. The thermal conductivity of the solid phase for Al-16.42 at.% Ag-4.97 at.% Cu and Al-16.57 at.% Ag-11.87 at.% Cu alloys and the thermal conductivity ratio of the liquid phase to the solid phase for Al-16.57 at.% Ag-11.87 at.% Cu alloy at the melting temperature were also measured with a radial heat flow apparatus and a Bridgman-type growth apparatus, respectively.
Determination of interfacial energies of solid Sn solution in the In-Bi-Sn ternary alloy
(ELSEVIER SCIENCE INC, 2009) Akbulut, S.; Ocak, Y.; Marasli, N.; Keslioglu, K.; Kaya, H.; Cadirli, E.
The equilibrated grain boundary groove shapes of solid Sn solution (Sn-40.14 at.% In-16.11 at.% Bi) in equilibrium with the In-Bi-Sn liquid (In-21.23 at.% Bi-19.04 at.% Sn) were observed from the quenched sample at 59 degrees C. Gibbs-Thomson coefficient, solid-liquid interfacial energy and grain boundary energy of the solid Sn solution have been determined from the observed grain boundary groove shapes. The thermal conductivity of solid phase for In-21.23 at.% Bi-19.04 at.% Sn alloy and the thermal conductivity ratio of liquid phase to solid phase at the melting temperature have also been measured with radial heat flow apparatus and Bridgman type growth apparatus, respectively. (C) 2008 Elsevier Inc. All rights reserved.
Determination of solid-liquid interfacial energies in the In-Bi-Sn ternary alloy
(IOP PUBLISHING LTD, 2008) Akbulut, S.; Ocak, Y.; Marasli, N.; Keslioglu, K.; Kaya, H.; Cadirli, E.
The equilibrated grain boundary groove shapes of solid In(2)Bi solution in equilibrium with the In-Bi-Sn eutectic liquid were observed from a quenched sample at 59 degrees C. The Gibbs-Thomson coefficient, solid-liquid interfacial energy and grain boundary energy of the solid In2Bi solution have been determined to be (1.42 +/- 0.07) x 10(-7) Km, (49.6 +/- 5.0) x 10(-3) Jm(-2) and (97.1 +/- 10.7) x 10(-3) Jm(-2), respectively, from the observed grain boundary groove shapes. The thermal conductivities of the solid phases for In-21.23 at% Bi-19.04 at% Sn and In-30.5 at% Bi-3 at% Sn alloys and the thermal conductivity ratio of the liquid phase to the solid phase for In-21.23 at% Bi-19.04 at% Sn have also been measured with a radial heat flow apparatus and a Bridgman type growth apparatus, respectively, at their melting temperature.
Determination of the thermal properties of Al-Zn-Mg alloy
(Redakcia Kovove Materialy, 2021) Cadirli, E.; Ustun, E.; Buyuk, U.; Kaya, H.
In this work, the thermal conductivity, enthalpy of fusion, specific heat capacity, and thermal diffusivity of the Al-5.5Zn-2.5Mg (wt.%) ternary alloy have been investigated. Thermal conductivity of as-cast Al-5.5Zn-2.5Mg alloy was measured using comparison cut bar method in the temperature range of 323-723 K. With the increase of temperature, thermal conductivity decreased gradually in as-cast Al-5.5Zn-2.5Mg alloy. The thermal temperature coefficient was calculated from the respective graph. The enthalpy of fusion and the specific heat capacity during the transformation were also determined. Thermal diffusivity changes were calculated as a function of temperature through the obtained thermal data. It was observed that thermal diffusivity values decreased with increasing temperature.
Directional cellular growth of Al-2 wt% Li bulk samples
(SPRINGER, 2009) Kaya, H.; Cadirli, E.; Gunduz, M.
Al-2 wt% Li alloy was prepared using metals of 99.99% high purity in the vacuum atmosphere. The bulk samples were directionally solidified upward with a constant growth rate, V, (similar to 8.30 mu m/s) and different temperature gradients, G, (3.11-6.06 K/mm) and also with a constant G (6.06 K/mm) and different V (8.3-164.70 mu m/s) in the directional solidification apparatus. The cellular spacings, lambda, were measured from both transverse and longitudinal section of the specimens and expressed as functions of solidification processing parameters, G and V, by using a linear regression analysis. The effects of the G and V on lambda, were investigated. The experimental results were compared with the current theoretical and numerical models, and similar previous experimental results.
Directional solidification and characterization of the Cd-Sn eutectic alloy
(ELSEVIER SCIENCE SA, 2007) Cadirli, E.; Kaya, H.; Gunduz, M.
The Cd-67.8 wt.% Sn eutectic alloy was prepared by melting together appropriate amounts of cadmium and tin (both of 99.99% purity) in a graphite crucible in a vacuum melting furnace. Then, this eutectic alloy was poured into graphite crucibles in a hot filling furnace and the samples were solidified. These samples were directionally solidified upward with different growth rate ranges (8.1-165 mu m/s) at a constant temperature gradient G (4.35 K/mm) in the Bridgman type directional solidification furnace. The lamellar spacings were measured using directional solidified samples. The variations of lambda with respect to V were determined by using linear regression analysis. The dependence of lamellar spacings X. on undercooling, Delta T, was also analysed. The variations of Delta T with V (at constant G) were investigated. According to these results, it has been found that with the increasing values of V, lambda decreases, whereas, Delta T increases for a constant G.lambda V-2, Delta T lambda and Delta TV-0.5 values were determined by using x, AT and V values. The results obtained in this work have been compared with the Jackson-Hunt eutectic theory and experimental results studied by Borland and Elliott, Clark and Elliott for the same alloy system, and also the similar alloy systems studied by Cadirli and Gunduz, Kaya et al. (c) 2006 Elsevier B.V. All rights reserved.
Directional solidification of Al-Cu-Ag alloy
(SPRINGER HEIDELBERG, 2009) Boyuk, U.; Marasli, N.; Kaya, H.; Cadirli, E.; Keslioglu, K.
Al-Cu-Ag alloy was prepared in a graphite crucible under a vacuum atmosphere. The samples were directionally solidified upwards under an argon atmosphere with different temperature gradients (G=3.99-8.79 K/mm), at a constant growth rate (V=8.30 mu m/s), and with different growth rates (V=1.83-498.25 mu m/s), at a constant gradient (G=8.79 K/mm) by using the Bridgman type directional solidification apparatus. The microstructure of Al-12.80-at.%-Cu-18.10-at.%-Ag alloy seems to be two fibrous and one lamellar structure. The interlamellar spacings (lambda) were measured from transverse sections of the samples. The dependence of interlamellar spacings (lambda) on the temperature gradient (G) and the growth rate (V) were determined by using linear regression analysis. According to these results it has been found that the value of lambda decreases with the increase of values of G and V. The values of lambda (2) V were also determined by using the measured values of lambda and V. The experimental results were compared with two-phase growth from binary and ternary eutectic liquid.
Directionally Solidified Al-Cu-Si-Fe Quaternary Eutectic Alloys
(Maik Nauka/Interperiodica/Springer, 2020) Buyuk, U.; Engin, S.; Kaya, H.; Cadirli, E.; Marasli, N.
Directional solidification of eutectic alloys attracts considerable attention because of microhardness, tensile strength, and electrical resistivity affected by eutectic structures. In this research, solidification processing of Al-Cu-Si-Fe (Al-26 wt % Cu-6.5 wt % Si-0.5 wt % Fe) quaternary eutectic alloy by directional solidification is examined. The alloy was prepared by vacuum furnace and directionally solidified in Bridgman-type equipment. During the directional solidification process, the growth rates utilized varied from 8.25 to 164.80 mu m/s. The Al-Cu-Si-Fe system showed a eutectic transformation, which resulted in the matrix Al, lamellar Al2Cu, plate Si, and plate Al7Cu2Fe phases. The eutectic spacing lambda(Al2Cu) between lamellae of Al2Cu, as well as-lambda (Si), between plates of Si phase,-was measured. Additionally, the microhardness, tensile strength, and electrical resistivity of the studied alloy were determined using directionally solidified samples, and the experimental relationships between them were obtained. It was found that the microhardness, tensile strength, and electrical resistivity were affected by both eutectic spacing and the growth rate.
Effect of solidification parameters on the microstructure of directionally solidified Sn-Bi-Zn lead-free solder
(KOREAN INST METALS MATERIALS, 2012) Cadirli, E.; Boyuk, U.; Kaya, H.; Marasli, N.
Sn-Bi-Zn lead free solder alloy was directionally solidified upward at a constant temperature gradient (G=3.99 K/mm) with a wide range of growth rates (8.3-478.6 mu m/s) and at a constant growth rate (V=8.3 mu m/s) with a wide range of temperature gradients (1.78-3.99 K/mm) using a Bridgman type directional solidification furnace. Wavelength-Dispersive X-ray Fluorescence spectrometry and X-ray diffraction were used to identify the compositions and phases in the microstructure. Dependence of eutectic spacings (lambda) on the growth rate (V), temperature gradient (G) and cooling rate (a(1a)) were determined using linear regression analysis. From the experimental results, it can be concluded that the values of lambda decrease with the increasing the values of V, G and a(1a). The value of lambda V-2 was determined using the measured values of lambda and V. The results obtained in the present work have been compared with previous results obtained for binary or ternary alloys.
Effect of solidification processing parameters on the cellular spacings in the Al-0.1 wt% Ti and Al-0.5 wt% Ti alloys
(ELSEVIER SCIENCE SA, 2007) Gunduz, M.; Kaya, H.; Cadirli, E.; Marasli, N.; Keslioglu, K.; Saatci, B.
The aim of this work is to investigate the relationship between solidification processing parameters (temperature gradient, G, growth rate, V, and cooling rate T), and cellular spacing, lambda, in the Al-0.1 wt% Ti and Al-0.5 wt% Ti alloys grown at high growth rates. In order to achieve this aim, the specimens were solidified under argon atmosphere and steady-state conditions upward with different temperature gradients, G at a constant growth rate, V and with different V at a constant G for the Al-Ti alloys in the Bridgman type directional solidification apparatus. The cellular spacing,. was measured and expressed as functions of solidification processing parameters, G, V and T by using a linear regression analysis. The results were compared with similar previous experimental work and current theoretical models suggested for cellular growth. (c) 2006 Elsevier B.V. All rights reserved.
Effects of Cooling Rate and Composition on Mechanical Properties of Directionally Solidified Pb100-x-Sn-x Solders
(SPRINGER, 2011) Cadirli, E.; Kaya, H.; Sahin, M.
Pb100-x-Sn-x solders (x = 5 wt.%, 10 wt.%, 20 wt.%, 35 wt.%, 50 wt.%, 60 wt.%, 61.9 wt.%, and 95 wt.%) were directionally solidified upward over a wide range of cooling rates (T) over dot (0.016 K s(-1) to 4.0 K s(-1)) by using a Bridgman-type directional solidification furnace. Microstructure parameters (primary dendrite arm spacing, lambda(1), and eutectic spacing, lambda(E)) and mechanical properties (microhardness, HV, and ultimate tensile strength, sigma) of the Pb100-x-Sn-x alloys were measured. The dependences of the microhardness and ultimate tensile strength on the cooling rate, microstructure parameters, and composition were determined. According to experimental results, the microhardness and ultimate tensile strength of the solidified samples increase with increasing cooling rate and Sn content, but decrease with increasing microstructure parameters.
Effects of growth rate and temperature gradient on the microstructure parameters in the directionally solidified succinonitrile-7.5 wt.% carbon tetrabromide alloy
(ELSEVIER SCIENCE SA, 2008) Marasli, N.; Keslioglu, K.; Arslan, B.; Kaya, H.; Cadirli, E.
Succinonitrile (SCN)-7.5 wt.% carbon tetrabromide (CTB) alloy was unidirectionally solidified with a constant growth rate (V = 33 mu m/s) at five different temperature gradients (G = 4.1-7.6 K/mm) and with a constant temperature gradient (G = 7.6 K/mm) at five different growth rates (V = 7.2-116.7 mu m/s). The primary dendrite arm spacings, secondary dendrite arm spacings, dendrite tip radius and mushy zone depths were measured. Theoretical models for the microstructure parameters have been compared with the experimental observations, and a comparison of our results with the current theoretical models and previous experimental results have also been made. (C) 2007 Elsevier B.V. All rights reserved.
Eutectic growth of unidirectionally solidified bismuth-cadmium alloy
(ELSEVIER SCIENCE SA, 2007) Kaya, H.; Cadirli, E.; Gunduz, M.
Bismuth (Bi)-Cadmium (Cd) eutectic alloy was melted in a graphite crucible under vacuum atmosphere. This alloy was directionally solidified upward with a constant growth rate, V (8.33 mu m/s), and different temperature gradient ranges, G (1.93-4.74 K/mm), and also with a constant G (4.74 K/mm), and different V (8.33-167.32 mu m/s) in the Bridgman type directional solidification furnace. The lamellar spacings lambda (lambda(a), lambda(a)*, lambda(m)*, lambda(M)*), were measured from both transverse section (lambda(a)) and longitudinal section (lambda(a)*, lambda(m)* lambda(M)*), of the specimens. The variations of lambda(i) with respect to G and V were determined by using linear regression analysis. The dependence of lamellar spacings lambda(i) on undercooling (Delta T) was also analysed. The variations of Delta T with G at constant V and with V at constant G were investigated. According to these results, it has been found that lambda(i) decreases with increasing values of G and V. Also Delta T increases with increasing V for a constant G and with increasing G for a given V, respectively lambda V-2, Delta T lambda, Delta TV-0.5 and lambda(2)G values were determined by using lambda(i), Delta T, V and G values. The results obtained in this work have been compared with the Jackson-Hunt eutectic theory and the similar experimental results (c) 2006 Published by Elsevier B.V.

Yazar "Kaya, H." seçeneğine göre listele

Sayfa Başına Sonuç

Sıralama seçenekleri